Addition of Sawdust and Polystyrene in the Elaboration of Adobe Blocks for Single-Family Homes and its Effect on Temperature Variation and Acoustic Conditioning in Ambato, Tungurahua

A. López, D. Chérrez, J. Guevara, G. Núñez

Abstract


This experiment evaluates the use of sawdust and expanded polystyrene (EPS) in the elaboration of adobe blocks as thermal and acoustic constructive elements with low environmental impact. To begin with, a soil selection and analysis process were carried out based on E-080 standard, then traditional adobe blocks with a percentage of 5%, 10% and 15% of sawdust and EPS were added in each mix. A suitable chamber was built to carry out the tests, based on specific standards, the chamber was divided into two rooms by a wall of the abode block with the addition of sawdust and expanded polystyrene using a 5mm layer of mortar to correct joint errors, this was considered appropriate for making temperature and sound measurements with the SPARK LXi Data logger (PS-3600A). Based on the Ecuadorian Construction Standard, comfortable reference values were determined for the measurements. After 28-day elaboration, the blocks were tested under compression. This test showed that all the analyzed samples exceeded the minimum resistance of 1MPa established in the E-080 standard. It was the highest compressive strength obtained in blocks with 5% of sawdust and EPS with a maximum resistance of 2.66 MPa. In addition, it was obtained that the wall made of 10% and 15% of adobe sawdust and EPS present the best performance to thermal variation and acoustic conditioning based on the standards NCh 352, NCh 851 - NCh 849 and NCh 2865.

Keywords


Adobe; resistance; sawdust; polystyrene; thermal; acoustic.

Full Text:

PDF

References


M. N. Azhar and L. A. Qureshi, "Experimental Study of Structural Behaviour of Chinese Bond Brick Masonry: A New Trend of Durable & Economical Construction in Pakistan," Journal of King Saud University-Engineering Sciences, 2020.

A. Gutiérrez, G. Quispe, A. Mendoza, H. Betancur, E. Ramos, "Confort térmico y el riesgo de infecciones respiratorias en los adultos mayores en la sierra rural del Perú," Revista Española de Geriatría y Gerontología, pp. 24-28, 2021.

M. Nurain, S. Adnan, S. Shahidan, A. Shah, "Strength and water absorption properties of light weightconcrete brick", IOP Conf. Ser. Mater. Sci. Eng. 513 (1) (2019), http://dx.doi.org/10.1088/1757-899X/513/1/012005.

R. S. Argento, J. Ferreyra, A. M. Anderson, M. F. Carrasco, A. González, and R. M. Grether, "Residuos de desmote de algodón aglomerados: su producción y aplicación en la construcción de viviendas," Ambiente Construído, vol. 19, pp. 127-145, 2019.

V. Angulo Zavaleta (2020), "Materiales alternativos sostenibles empleados en la construcción: una revisión a la literatura científica," Available: https://repositorio.upn.edu.pe/handle/11537/23755.

A. Michaelowa, A. Galante, L. Lo Re, V. Villa, C. Illueca, P. Gómez, et al., "Concepto de implementación del mecanismo sectorial de mitigación en el sector de los residuos en Ecuador. (Documento principal)," ed: CAF, 2019.

K. Raju and S. Ravindhar, "Multiple categories of bricks used for construction–A Review," in IOP Conference Series: Materials Science and Engineering, 2020, p. 012122.

A. Mohajerani, M. Ashdown, L. Abdihashi, and M. Nazem, "Expanded polystyrene geofoam in pavement construction," Construction and Building Materials, vol. 157, pp. 438-448, 2017.

S. Siswosukarto, A. Saputra, and I. G. Y. Kafrain, "Utilization of polystyrene waste for wall panel to produce green construction materials," Procedia engineering, vol. 171, pp. 664-671, 2017.

T. Bowen, "A Best Practices Manual for Using Compressed Earth Blocks in Sustainable, Home Construction in Indian Country", University of Colorado Boulder, (2017), pp. 45

C. Fioriti, R. Segantini, J. Pinheiro, J. Akasaki, and F. Spósito, "Bloques de mampostería de hormigón liviano fabricados con caucho de neumáticos y metacaolín," Revista ingeniería de construcción, vol. 35, pp. 295-307, 2020.

C. Ponce-Palafox, J. Carrillo, and A. López-Montelongo, "Fabricación de ladrillos con polvo-residuo de mármol en México Propiedades físicas y mecánicas del polvo-residuo de mármol de la provincia de la Comarca Lagunera, en México," Revista de Arquitectura (Bogotá), vol. 22, pp. 106-113, 2020.

M. Premkumar, G. Devi, R. Sowmya, " Design and Implementation of Brick Making Machine Integrated with Smart IIoT Application," International Journal of Computing and Digital Systems, vol. 9, 2020.

S. Marathe, I. Mithanthaya, and S. Shetty, "Strength behaviour of masonry blocks produced using green concrete," in Sustainable Construction and Building Materials, ed: Springer, 2019, pp. 33-40.

J. Canivell, J. Martin-del-Rio, F. Alejandre, J. García, A. Jimenez, "Considerations on the physical and mechanical properties of lime-stabilized rammed earth walls and their evaluation by ultrasonic pulse velocity testing". Const. Build. Mater., 2018, pp. 826-836.

R. Abid, N. Kamoun, F. Jamoussi, and H. El Feki, "Fabrication and properties of compressed earth brick from local Tunisian raw materials," Boletín de la Sociedad Española de Cerámica y Vidrio, 2021.

M. Madrid, A. Orbe, H. Carré, and Y. García, "Thermal performance of sawdust and lime-mud concrete masonry units," Construction and Building Materials, vol. 169, pp. 113-123, 2018.

J. Véliz-Párraga and D. González-Couret, "Vivienda de interés social en Portoviejo. Ambiente térmico interior," AUS [Arquitectura/Urbanismo/Sustentabilidad], pp. 35-41, 2019.

C.Lima, F. Ribeiro, G. Isaia, M. Mancio, "Concretes with binary mixtures of artificial pozzolans and concrete demolition waste," Ambiente Construído, vol. 20, pp. 177-188, 2020.

J. R. Lopez Huaman, "Medidas de atenuación de señal 3G y 4G en estructuras construidas por adobe (measurements of 3G and 4G signal attenuation in adobe buildings structures)," 2020.

V. B. Benites Zapata, "Adobe estabilizado con extracto de cabuya (Furcraea andina)," 2017.

V. A. Chicaiza Llumipanta, "Análisis comparativo de la resistencia a compresión entre bloques tradicionales y bloques elaborados con poliestireno expandido granular y bloques elaborados con tusa de maíz triturado como sustituto parcial del agregado grueso," Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, 2017.

J. H. Lazaro Reynoso, J. L. Villalta Preciado, C. E. Colonio Reyes, D. E. Fernandez Quispe, and T. N. Llanos Sanchez, "Casas estructuradas con centro de poliestireno expandido," 2017.

F. Wang, N. Kyriakides, C. Chrysostomou, E. Eleftheriou, R. Votsis, and R. Illampas, "Experimental research on bond behaviour of fabric reinforced cementitious matrix composites for retrofitting masonry walls," International Journal of Concrete Structures and Materials, vol. 15, pp. 1-17, 2021.

D. El Peruano, "Ministerio de Vivienda, Construcción y Saneamiento," Norma E. 080-RNE. Diseño y construcción con tierra reforzada.

N. INEN, "“NTE INEN 692: Determinación del límite plástico.,†vol. 0818, pp. 1–10, 1982.," 1982.

N. INEN, "“NTE INEN 696: Ãridos. Analisis granulométricos en los áridos, fino y grueso.,†Inst. Ecuatoriano Norm., vol. 0696, pp. 1–12, 2011.," 2011.

D. Y. Hernández Endara, "Determinación de las características físicas y mecánicas del suelo para implantación de edificaciones de categoría baja en la ciudadela 24 de Mayo, ciudad Jipijapa," JIPIJAPA-UNESUM, 2018.

A. D. Ortega and H. Gil, "Estudio del comportamiento mecánico de morteros modificados con fibras de aserrín bajo esfuerzos de compresión," Revista Científica Ingeniería y Desarrollo, vol. 37, pp. 20-35, 2019.

B. Zviagina, V. Drits, O. Dorzhieva, "Distinguishing features and identification criteria for K-dioctahedral 1M Micas (illite-aluminoceladonite and illite-glauconite-celadonite series) from middle-infrared spectroscopy data," Minerals, vol. 10, p. 153, 10.3390/min10020153, 2020.

C. Costa, D. Arduin, F. Rocha, and A. Velosa, "Adobe blocks in the center of Portugal: Main characteristics," International Journal of Architectural Heritage, vol. 15, pp. 467-478, 2021.

Y. Qin, Y. He, J. E. Hiller, and G. Mei, "A new water-retaining paver block for reducing runoff and cooling pavement," Journal of Cleaner Production, vol. 199, pp. 948-956, 2018.

C. Babé, D. K. Kidmo, A. Tom, R. R. N. Mvondo, R. B. E. Boum, and N. Djongyang, "Thermomechanical characterization and durability of adobes reinforced with millet waste fibers (sorghum bicolor)," Case Studies in Construction Materials, vol. 13, p. e00422, 2020.

S. P. Cabrera, Y. G. Aranda-Jiménez, E. J. Suárez-Domínguez, and R. Rotondaro, "Bloques de Tierra Comprimida (BTC) estabilizados con cal y cemento. Evaluación de su impacto ambiental y su resistencia a compresión," Revista hábitat sustentable, vol. 10, pp. 70-81, 2020.

R. Suda, T. Kiefer, C. Schranz, and J. Füssl, "A finite-element-based approach to quantify the impact of bed joint reinforcement on the compressive strength of vertically perforated clay block masonry," Engineering Structures, vol. 239, p. 112277, 2021.

E. A. Paguay Córdova, "La adición de botellas plásticas PET en la elaboración de bloques alivianados para viviendas unifamiliares y su efecto en la variación de temperatura y acondicionamiento acústico en el cantón Ambato, provincia de Tungurahua," Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica …, 2019.

S. R. Cabay Cepeda, "La adición de bolsas plásticas en la elaboración de bloques de adobe para viviendas unifamiliares y su efecto en la variación de temperatura y acondicionamiento acústico en el cantón Ambato, provincia de Tungurahua," Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica …, 2019.

C. N. Orcaistegui Venegas, "Evaluación técnica y económica de aplicar medidas de reacondicionamiento en viviendas existentes," 2018.

A. Ullauri, N. Friend, and J. Barzola, "Análisis físico-mecánico de morteros asfálticos compuestos a partir de materiales reciclados," Revista Universidad y Sociedad, vol. 10, pp. 245-254, 2018.

A. Marquínes, E. Tejeira, E. Aulestia, M. Lezcano, S. Franco, J. Peren, "Evaluación del nivel de iluminación natural en una oficina del edificio 3835 del International Business Park,". SusBCity, vol. 2(1), pp. 1-8, 2020.

R. M. Gandia, F. C. Gomes, A. A. Corrêa, M. C. Rodrigues, and D. B. Marin, "Physical, mechanical and thermal behaviour of adobe stabilized with the sludge of wastewater treatment plants," Engenharia Agrícola, vol. 39, pp. 684-697, 2019.

H.-Y. Liu, H.-S. Wu, and C.-P. Chou, "Study on engineering and thermal properties of environment-friendly lightweight brick made from Kinmen oyster shells & sorghum waste," Construction and Building Materials, vol. 246, p. 118367, 2020.

MIDUVI, "NEC-HS-EE: Eficiencia energética en la construcción en Ecuador," 2018.

X. B. Castillo Izurieta, "La importancia de la aplicación de las normas NEC-norma ecuatoriana de la construcción, en la utilización del vidrio en la construcción," Universidad de Guayaquil Facultad de Ciencias Administrativas, 2020.

V. G. Chimbo Andy, "Análisis de la resistencia a la compresión de ladrillos prensados interconectables elaborados de barro, cangahua y puzolana, con adiciones de cemento, cumpliendo la norma ecuatoriana de la construcción (NEC 2015)," Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica …, 2017.

R. M. Garay and N. Pino G, "Proyecto Vivienda de Emergencia, Parte 3, Comportamiento acústico," Revista de la construcción, vol. 18, pp. 96-110, 2019.

M. Machimbarrena, B. Rasmussen, and C. R. Alves Monteiro, "Regulatory sound insulation requirements in South America-Status for housing, schools, hospitals and office buildings," in INTER-NOISE and NOISE-CON Congress and Conference Proceedings, 2019, pp. 7470-7481.

Y. Rodríguez Cisneros and W. Baldeón Quispe, "Evaluación del ruido y el confort acústico en la Biblioteca Agrícola Nacional. Lima, Perú," Medicina y Seguridad del Trabajo, vol. 64, pp. 17-32, 2018.

C. INN | Instituto Nacional de Normalización, "NCh352.Of2000- Aislación acústica - Parte 1: Construcciones de uso habitacional - Requisitos mínimos y ensayos (extracto)," 2000.

H. A. Pino Escobar, "La adición de aserrín y poliestireno en la elaboración de bloques de adobe para viviendas unifamiliares y su efecto en la variación de temperatura y acondicionamiento acústico en el cantón Ambato, provincia de Tungurahua," Universidad Técnica de Ambato. Facultad de Ingeniería Civil y Mecánica, 2019.




DOI: http://dx.doi.org/10.18517/ijaseit.12.2.15823

Refbacks

  • There are currently no refbacks.



Published by INSIGHT - Indonesian Society for Knowledge and Human Development